That Is Equipped The source code for this pergola layout is freely available, and it features enclosed sides that come complete with side tables built right in.
In addition, a downloadable version of the blueprint may be found here. It is meant to take the form of a tranquil retreat in the Equipped backyard.
And it would look stunning if it were furnished with a swing, lounge chairs, or a conversation set of some kind.
You can receive free instructions for building a pergola using the do-it-yourself (DIY) approach from Ana-White.com. The Equipped directions are broken down into step-by-step format.
On a surface that is level, carefully set stakes that are manufactured out of timber measuring 6×6 at a distance of 120 inches from one another.
This distance should be measured beginning on the Equipped outside of one structure and working our way around to the outside of the other structure.
Notations should be made on the rafters at 141 inches along their length and 10.5 inches in from either end of the Equipped rafters Carry out this action on both ends.
You will be able to connect the two posts by first predrilling a total of four holes in the two posts, and then using external decking screws that are three and a half inches in length to link them to one another.
Before you begin attaching the rafters, you need to make sure that the tops and bottoms of the Equipped two posts are parallel to one another.
This is a necessary step before you can move on to the next step. Before beginning the Equipped process of attachment, this step absolutely must be completed.
NOTE: If you want to cut decorative tails into the rafters (see step 3), make sure you do so on sawhorses that have been erected on the ground before you join the rafters to the pergola.
This will ensure that the tails are cut cleanly and accurately. Because of this, you can have peace of mind knowing that the Equipped cuts will be accurate.
Make sure that each of your replies is positioned correctly next to the other responses that have been submitted in the Equipped thread, and that this applies to all of your posts.
After that, secure the cross supports to the pillars and the rafters in the locations where they will be providing support for the roof by using the Equipped appropriate fasteners.
When mounting to rafters, make sure you use deck screws that have a combined length of at least two and a half inches.
Either you drill pocket holes into the posts that are 1-1/2 inches in diameter and then use pocket hole screws that are 2-1/2 inches in length to secure the Equipped brackets to the posts.
Or you may use metal brackets instead of wood brackets to achieve the same result. Either way, the result will be the Equipped same.
The first phase in the Equipped process of building shelves comprises employing predrilled holes to accept outside deck screws with a length of 2-1/2 inches.
Affixing 2x4s with a length of 17-1/2 inches to 2x6s with a length of 66 inches, and utilizing two screws for each connection in the assembly of the Equipped shelves.
Deck screws with a length of 3-1/2 inches should be used whenever you are mounting shelves to their supports. After holes have been drilled into the Equipped components.
Those holes will be passed through the 2x4s and the 2x6s before the Equipped components may be joined to one another.
To link 2×6 boards with a length of 20 and a half inches to the ends of 2×6 shelf boards, you will need to drill holes and make use of wood screws with a length of two and a half inches.
Make sure that the backrests of the seats are in the Equipped appropriate places by adjusting them as necessary Wood screws are going to be used to join these boards together.
Deck screws with a length of two and a half inches are utilized in the process of attaching components to a framework that is constructed out of 2x4s.
After the holes have been predrilled, these screws are subsequently fastened to the structure by inserting them into the holes.
If this is something that piques your attention, you have the alternative of utilizing the jigsaw to carve attractive motifs into the tails of the rafters.
Learn more: Woodworking Project
Related Stories:
